儀器說明
DLRO 10和DLRO 10X設置了低阻測量的標準。DLRO 10和DLRO 10X都是全自動儀器,選擇一個合適的測試電流一直到10A直流,測得的阻抗阻值從0.1μΩ到2000Ω。
對于想在測試過程中有更多控制的使用者來說,DLRO 10X通過控制面板上的2個鍵來在儀器的菜單系統中選擇最大測試電流。
DLRO 10X添加了下載功能,他能把結果實時下載下來,也可以儲存在儀器中,以后在下載到計算機中去。
兩個儀器都組裝在一個結實,輕便的盒子中,使儀器能放在家里,能方便的帶到工地上去,能帶到展覽會上去。很輕能夠把他輕松的掛在脖子上,而且他們很小,能夠帶到以前因為門口太小而帶不到的地方去。
DLR10是用一個大的41/2數字LED來顯示結果的,而DLR10X用一個大的背光LCD來顯示結果。通常地,儀器用促發和逆轉電流的測量方法來消除作用在測試樣品上的停滯電壓的影響。
在3秒內將會顯示其平均值,這個值的基本精確度是0.2%。DLRO 10X顯示值是促進和逆轉這2中測量的平均值。
DLRO 10X允許用戶設置通過上限和下限值,這樣就能使試驗很輕松的進行。在試驗結束后,DLRO 10X能夠儲存測試結果,并且可以存儲給測試結果加的注釋。
為了幫助操作者能安全方便的使用本儀器,DLRO 10和DLRO 10X都提供了一對1.2m長的手拿導線。在其中一個探測器上有一個LED顯示,顯示的內容是和儀器的面板上的顯示是一樣的,他顯示的是,4端都已經連接上了,有高電壓作用在負載倆端,在負載放電的時候有電流流經。在測試導線時候用探針,夾鉗,凱爾文夾子可以得到滿偏量程。
DLRO 10和DLRO 10X儀器由鎳氫電池供電。電池包是可以取下來的,所以在一個電池用完后,可以取下來去充電,然后在換一塊電池。盡管用12V電池或者標準的120/230V交流把電池充滿需要4個小時,但是充電2個小時,可以充滿電池的90%。在電池包上會顯示電池的狀況,就算電池沒放在儀器中也可以看的到。
DLRO 10X上有一個RS232通信端口,通過他可以把數據實時傳輸出去,也可以先存儲起來再下載到PC中。
DLRO 10X能夠儲存700組數據和在200字以內的注釋,這些注釋可以通過控制面板上的鍵盤來輸入進去。
測量方法:
DLRO 10和 DLRO 10X都提供了很多測量方法,例如,正常的,自動的,連續的和感應的模式。
DLRO 10會顯示用 促發和逆轉電流測得的值的平均值,DLRO10X會顯示用促發和逆轉電流測的倆個獨立的值和這倆個值的平均值。
正常模式 在測試導線都連接好了,四端也被檢測了,促發和逆轉電流都已經準備好,就按下儀器控制面板上的TEST按鈕。
自動模式 只要簡單的把4個探針連接上,促發和逆轉電流準備好,測試就可以開始了。推薦在使用一雙手桿時使用此模式,過一段時間探針就要移到另一個負載上去,不需要按儀器的TEST按鈕,試驗就可以進行了。
連續模式 允許對同一個樣品測試幾遍。只需要簡單的把測試導線連接上,按下TEST鍵就可以進行試驗了。儀器將會每3秒就對樣品從新測量一次,直到電路斷開。
感應模式 他是用來測試感應電路的。當測試感應電路的時候要等電壓穩定。這就意味著測試要很多秒鐘甚至是幾分鐘。在測試導線連接好了,按下了TEST按鈕后。儀器就會向樣品輸出一個電流,然后再等電壓穩定。如果可能電流將會增強,重復這個步驟再三直到電壓穩定并且降到15mV到200mV。儀器上的讀數將會減少,直到電壓穩定后的真值。在結果穩定后,操作者就可以按下TEST按鈕來結束實驗。測量僅僅使用了促發電流。
單向模式 僅僅只用DLRO 10X有。他僅僅只向一個方向提供電流。他不能消除停滯電動勢的影響,但是能夠加速試驗進程。探針連接上后,試驗就會自動進行。
儀器應用
對低阻的測量眾所周知是非常需要的。主要針對下列設備進行支流阻抗測量:
-- 開關和接點斷路器阻抗
-- 母線和電纜線接頭
-- 飛機扛架的連接和靜態控制電路
-- 焊接接縫的完整
-- 高達600V的電池系統的內部連接
-- 電阻分量的質量控制
-- 變壓器和電動機繞組阻抗
-- 鐵軌和軌道之間的粘合
-- 金屬合金,焊縫和保險絲阻抗
-- 石墨電極和其他合成物
-- 金屬絲和電纜線阻抗
-- 發射天線和避雷針
特性和優點
-- 小巧,輕便和手提式設計使儀器移動到想要移動的任何地方,減少需要額外的導線和2個人來操作
-- 四線式原理設計能夠真實的測的被測物品的阻抗
-- LED(DLRO 10)和LCD(DLRO 10X)能夠清楚的顯示測試結果并減少人為的失誤。
-- 用觸發和逆轉電流的測量方法來消除作用在測試樣品上的停滯電壓的影響
-- 檢查測試時候的噪音,減少有可能對測試結果有影響的因素
-- 自動探測P和C電路的連貫性,防止由于高阻抗連接而產生的錯誤的讀數。
-- 電池??檣夏芄輝詰緋孛緩鴕瞧髁擁氖焙螄允臼S嗟牡緦?。
-- 在DLRO 10X上的 RS232接口能把測試結果實時傳輸或者儲存起來以后在下載到電腦中去
|
滿偏電壓 |
測試電流 |
滿偏值 |
分辨率 |
精確度 |
阻抗 |
感抗 |
阻抗 |
感抗 |
1.9999 mΩ |
0.1 μΩ |
±0.2% ±0.2μΩ |
20 mV |
n/a |
10A |
n/a |
19.999 mΩ |
1 μΩ |
±0.2% ±2 μΩ |
20 mV |
20 mV |
1A |
1A |
199.99 mΩ |
10 μΩ |
±0.2% ±20 μΩ |
20 mV |
200 mV |
100 mA |
1A |
1.9999Ω |
100 μΩ |
±0.2% ±0.2 mΩ |
20 mV |
200 mV |
10 mA |
100 mA |
19.999Ω |
1 mΩ |
±0.2% ±2 mΩ |
20 mV |
200 mV |
1 mA |
10 mA |
199.99Ω |
10 mΩ |
±0.2% ±20 mΩ |
20 mV |
200 mV |
100 μA |
1 mA |
1999.9 Ω |
100 mΩ |
±0.2% ±0.2Ω |
200 mV |
200 mV |
100 μA |
100 μA |

DLRO10 和 DLRO10X 訂貨注意: |
標配包含: |
7 Ah NiMH battery module. 6340-101(電池) |
DH4 Duplex handspikes (2),one with indicator lights. 1.2m / 4 ft 6111-503(二個測試槍,其中一個帶指示燈) |
Battery charger for operation from 115/230 V .50/60Hz supply. 6280-333(充電器) |
Cigar lighter adapter for battery charging. 6280-332(點煙器適配器) |
User guide. 6172-473(使用手冊(英文)) |
Warranty book. 6170-618(保修卡) |
|
DLRO10 和 DLRO10X 一般選件: |
Carrying case for DLRO10/10X and all standard accessories. 6380-138 (可裝主機和所有標配配件的儀器箱) |
Carrying case for optional lead sets. 18313(可裝選配測試線的儀器箱) |
Calibration Shunt,10Ω, current rating 1 mA. 249000(10Ω標定分流器) |
Calibration Shunt, 1Ω, current rating 10 mA. 249001(1Ω標定分流器) |
Calibration Shunt, 100mΩ current rating 1A. 249002(100mΩ標定分流器) |
Calibration Shunt, 10mΩ current rating 10 A. 249003(10mΩ標定分流器) |
Needle point 25940-012(探針) |
Serrated end 25940-014(探針) |
|
DLRO10 和 DLRO10X 測試線選件: |
DH5 straight duplex handspikes (2).One has indicator lights. 2.5m/8ft 6111-517 (DH5雙測試槍,其中一個帶指示燈,2.5米線) |
DH6 Duplex handspikes (2) suitable for working on 600 V. systems. 2.5m/8ft 6111-518(DH6雙測試槍,600V, 2.5米線) |
Duplex Handspikes (2) with springloaded helical contacts. 2m/7ft 242011-7(雙測試槍,彈簧觸點,2米線) |
Duplex Handspikes (2) with springloaded helical contacts. 2.5m/8ft 6111-022(雙測試槍,彈簧觸點,2.5米線) |
Duplex Handspikes (2) with springloaded helical contacts. 5.5m/18ft 242011-18(雙測試槍,彈簧觸點,5.5米線) |
only 1 lead supplied 6m/20ft 6111-023(一條6米測試線) |
only 1 lead supplied 9m/30ft 242011-30(一條9米測試線) |
Straight Duplex Handspikes (2)Heavy Duty with fixed contacts. 2m/7ft 242002-7(雙測試槍,大功率,固定觸點,2米線) |
Straight Duplex Handspikes (2)Heavy Duty with fixed contacts. 5.5m/18ft 242002-18(雙測試槍,大功率,固定觸點,5.5米線) |
Straight Duplex Handspikes (2)Heavy Duty with fixed contacts. 9m/30ft 242002-30 (雙測試槍,大功率,固定觸點,9米線) |
Duplex Heavy Duty 5cm (2") C-Clamps(2) 2m/7ft 242004-7
(5cm開口,雙測試鉗,2米線) |
Duplex Heavy Duty 5cm (2") C-Clamps(2) 5.5m/18ft 242004-18
(5cm開口,雙測試鉗,5.5米線) |
Duplex Heavy Duty 5cm (2") C-Clamps(2) 9m/30ft 242004-30
(5cm開口,雙測試鉗,9米線) |
Duplex handspikes with replaceable Needle Points 2m/7ft 242003-7
(雙測試槍,探針可更換) |
Duplex 1.27 cm (1/2 ")Kelvin Clips.(2) gold plated 2m/7ft 241005-7
(雙1.27cm開口Kelvin測試夾,鍍金,2米測試線) |
Duplex 1.27 cm (1/2 ")Kelvin Clips.(2) silver plated 2m/7ft 242005-7
(雙1.27cm開口Kelvin測試夾,鍍銀,2米測試線) |
Duplex 3.8 cm (11/2")Kelvin Clips.(2) 2m/7ft 242006-7(雙3.8cm開口Kelvin測試夾,2米測試線) |
Duplex 3.8 cm (11/2")Kelvin Clips.(2) 5.5m/18ft 242006-18
(雙3.8cm開口Kelvin測試夾,5.5米測試線) |
Duplex 3.8 cm (11/2")Kelvin Clips.(2) 9m/30ft 242006-30
(雙3.8cm開口Kelvin測試夾,9米測試線) |
 
 



Megger DLRO10
Digital Low Resistance Ohmmeters
• Accurate results in under three seconds
• Auto current reversal cancels standing emfs
• Fuse protected to 600 V
• NiMH battery reduces weight
• 250 mW power limit (with optional override) to avoid heating the test sample
• Automatically detects continuity in potential and current connections
• Visible warning of high voltages present at the terminals
• Visible warning of current flowing in the test sample
• Multiple operating modes including fully automatic |
|
The MEGGER DLRO10 bring new standards to low resistance measurement. A fully automatic instrument, selecting the most suitable test current, up to 10 A dc to measure resistance from 0.1 µΩ to 2000 Ω on one of seven ranges.
The DLRO10 is built into a strong, lightweight case that is equally at home in the field or in the laboratory. Light enough to be worn around the neck, they are small enough to be taken into areas which were previously too small to access. DLRO 10 uses a large, bright 4-1/2-digit LED display.
|
Megger DLRO10X
Digital Low Resistance Ohmmeters
• Accurate results in under three seconds
• Auto current reversal cancels standing emfs
• Fuse protected to 600 V
• NiMH battery reduces weight
• 250 mW power limit (with optional override) to avoid heating the test sample
• Automatically detects continuity in potential and current connections
• Visible warning of high voltages present at the terminals
• Visible warning of current flowing in the test sample
• Multiple operating modes including fully automatic
• Alpha-numeric keypad for entering test notes
• User setable high and low limits
• Autoranging with Manual option
• Printer output and memory |
|
The MEGGER DUCTER DLRO10 and DUCTER DLRO10X bring new standards to low resistance measurement. Both are fully automatic instruments, selecting the most suitable test current, up to 10 A dc to measure resistance from 0.1 µΩ to 2000 Ω on one of seven ranges. For users who desire more control over the measurement process, DLRO 10X uses a menu system controlled by a two-axis paddle to allow manual selection of the test current. DLRO10X also adds real-time download of results and on-board storage for later download to a PC.
Both instruments are built into a strong, lightweight case that is equally at home in the field or in the laboratory. Light enough to be worn around the neck, they are small enough to be taken into areas which were previously too small to access. DLRO 10 uses a large, bright 4-1/2-digit LED display while DLRO 10X has a large, backlit LCD display.
|